Item #1001620687
Model #HD-2703-WH
HD-2703-BZ
USE AND CARE GUIDE
MOTION SECURITY LIGHT
Questions, problems, missing parts? Before returning to the store,
call Defiant Customer Service
8 a.m. - 7 p.m., EST, Monday - Friday, 9 a.m. - 6 p.m., EST, Saturday
1-866-308-3976
HOMEDEPOT.COM
THANK YOU
We appreciate the trust and confidence you have placed in Defiant through the purchase of this motion security light.
We strive to continually create quality products designed to enhance your home. Visit us online to see our full line of
products available for your home improvement needs. Thank you for choosing Defiant!
151209-IQA HD-2703-FA.indd
1
9/12/2015 10:18:34 AM
Warranty
5-YEAR WARRANTY
Specifications
Detection range
sensing angle
Time delay
Up to 70 ft. (21m) - Varies with surrounding temperature
Up to 270°
1, 5, or 10 minutes
Hi-LO timer
OFF, Dusk-to-Dawn, Seasonal adjusted timer mode
Auto, Manual, Eco, Smart
Operating modes
Pre-Installation
PLanninG insTaLLaTiOn
Before installating the light fixture, ensure that all parts are present (see Hardware Included on page 4). If any part is
missing or damaged, do not attempt to assemble, install, or operate this light fixture.
Estimated installation time: 30 minutes
TOOLs rEQuirED
Phillips
screwdriver
Flathead
screwdriver
Pliers
Wire strippers/
cutters
Circuit tester
Work gloves
Electrical tape
Silicone sealant
Ladder
Safety goggles
3
HOMEDEPOT.com
Please contact 1-866-308-3976 for further assistance.
151209-IQA HD-2703-FA.indd
3
9/12/2015 10:18:34 AM
Pre-Installation (continued)
HArdwAre iNclUded
NOTE: Hardware shown not to scale
AA
DD
BB
CC
EE
FF
M4 X 1.6”
M4 X 1.9”
GG
HH
II
Part
description
Quantity
AA
Wire connector
2
BB
CC
DD
EE
FF
Connector wire (black and white)
Gasket
1
1
1
2
2
2
Mounting bracket
Mounting bracket screw 1
Mounting bracket screw 2
Mounting bracket screw
(M4 X 1.6”)
GG
HH
II
Mounting bracket screw
(M4 X 1.9”)
2
2
Decorative nut
4
151209-IQA HD-2703-FA.indd
4
9/12/2015 10:18:35 AM
Pre-Installation (continued)
PAcKAge cONTeNTs
B
A
C
Part
description
Quantity
A
Main body
1
B
C
Lamp head
PIR lens
2
1
MOUNTiNg lOcATiONs
□
Determine the mounting location - a wall or under
an eave.
□
Position lamp head (B) in the general direction of
the desired light coverage and tighten the screws
(3) if needed.
1
2
Wall Mount
B
2
1
A
Eave Mount
3
3
C
□
Rotate the body up to change from wall mount to
eave mount as per drawing below.
5
HOMEDEPOT.com
Please contact 1-866-308-3976 for further assistance.
151209-IQA HD-2703-FA.indd
5
9/12/2015 10:18:35 AM
Installation
installing the Mounting Bracket
1
WARNING: Turn the power off at the circuit breaker or
fuse. Place tape over the circuit breaker switch and verify
power is off at the light fixture.
NOTE: Firmly pull on the mounting bracket to verify it is
securely mounted to the junction box. If necessary, use the
screws that were removed from the existing light fixture.
□
□
Remove the existing light fixture.
Thread the shorter of the two sets of long
mounting bracket screws (GG) all the way
through the outer mounting bracket from the
back, so the threads come out through the front.
GG
or
□
Install the mounting bracket to the junction box
by using the screws (EE or FF) and going through
the slots of the rear mounting bracket.
HH
DD
EE or FF
Select the screws (EE or FF) that best fit the holes
of your junction box, or if necessary, reuse the
original screws.
wiring the light Fixture
2
□
CAUTION: Do not cut any wires with factory installed
wire connectors or remove the wire connectors.
Connect the connector wire (BB) to the junction
box wires with wire connectors (AA):
□
□
White to white
Black to black
□
Connect the ground wire to the ground screws (1)
on the mounting bracket, then tighten the ground
screw.
1
Attaching the gasket
3
□
Insert the wires with connector into the junction
box.
□
Attach the gasket (CC) to the mounting bracket.
See final gasket position in the diagram in
section 4 for your reference.
□
Tighten the mounting bracket screws (2).
CC
2
6
151209-IQA HD-2703-FA.indd
6
9/12/2015 10:18:35 AM
Installation (continued)
Mounting the light Fixture
4
□
Plug the connector (BB) into the connector on
the back of the fixture (A).
NOTE: Make sure all the wires are inside the junction box
before attaching the main body (A) to the junction box.
□
Align the main body (A) to the mounting bracket
screws (GG) and slide the light fixture over the
screws. Firmly push the light fixture against the
junction box, so the mounting bracket screws
come out through the holes on the front of the
light fixture.
A
BB
II
□
Attach decorative nuts to the mounting bracket
screws and tighten.
II
GG or HH
note: If the mounting bracket screws (GG) are not long enough to allow the decorative nuts (II) to be
threaded on them, then you will need to replace the shorter set of screws (GG) with the longer set of
screws (HH). This is usually due to the junction box being recessed into the wall.
If the longer mounting bracket screws are necessary, remove the fixture from the screws, unplug the
connector wire, remove the mounting bracket and replace the mounting bracket screws with the longer
screws. Repeat the installation steps starting with section 1.
caulking Around the light
Fixture
Caulk around the edge of the main body (A) and
the mounting surface with silicone sealant
5
□
(not included).
A
Operation
lamp Adjustment
1
□
Turn the power on at the circuit breaker or fuse
and turn on the wall switch.
1
1
□
Hinge (1) can tilt the lamps up.
Hinge (2) can pan the lights in and out.
Tighten screws (3) if loose.
35º
40º
□
67º
NOTE: Do not rotate the bulb holders more than 180°
from the factory setting.
7
HOMEDEPOT.com
Please contact 1-866-308-3976 for further assistance.
151209-IQA HD-2703-FA.indd
7
9/12/2015 10:18:36 AM
Operation (continued)
setting the sensor for Testing
sensor Head Adjustment
3
2
□
Rotate the motion sensor (C) so the controls
face toward the ground.
□
Turn on power. Conduct a walk test to adjust
the sensor coverage area. Sensor will be in
TEST mode automatically for 2 minutes. Lights
will come on for approximately 2-3 seconds in
TEST mode.
□
The sensor can be tilted up and down,
as well as rotated left and right.
□
Sensor stays in TEST mode until it no longer
senses motion for more than 2 minutes,
then it will revert to the AUTO sensing mode.
NOTE: The motion sensor will need to completely warm
up (60 seconds) before beginning the setup process.
C
Adjusting the Motion sensor
detection Zone
Turn on the circuit breaker or fuse and the light
switch.
Adjusting the Hi/lO light level
5
4
□
HI level security lighting and LO level accent lighting.
HI-LO feature is off. Works with motion
sensor after dark at 100% brightness.
□
□
□
□
□
Perform a “walk test”. Walk in an arc across the
front of the motion sensor (C).
Watch the light. The light will come on indicating
motion has been detected.
(Dusk to Dawn Mode): At Dusk, lights will
turn On at 30% of normal brightness and
then will dim to 15% in the middle of the
night hours. The middle of the night is
calculated automatically by the sensor. At
Dawn, lights will turn Off automatically.
Stop, wait for the light to turn off, and then begin
walking again.
Continue this process until the detection zone
has been established.
Adjust the sensor up, down, or side to side to
change the motion sensor (C) detection zone.
(Timer Mode): Seasonally Adjusted Timer:
At Dusk, lights turn On at 30% and then
shut Off in the middle of the night hours
(calculated automatically by the sensor).
HI- LO
270°
C
8
151209-IQA HD-2703-FA.indd
8
9/12/2015 10:18:36 AM
Operation (continued)
Adjust the dusk learn
Adjusting the Time
ECO mode:
Motion sensor lighting is set to minimize
power usage. Lights turn on with motion for
10 seconds and continue to stay on as long
as motion is detected. Lights will dim to warn
that lights will be shutting off soon.
6
7
If desired, you can set the level of darkness at
which the sensor becomes active and at which the
Hi-Lo feature comes on in the “Lo” accent mode.
□
□
Press once: To learn the current level of
brightness and set this as your new “Dusk”
level.
sMarT mode:
Sensor learns from your behavior to
automatically adjust the time.
□
□
Press twice within 5 seconds: Back to factory
default setting (+/- 5 lux)
□
□
Press and hold the button more than 5 seconds:
For example, after multiple detections in a
short period, motion sensor automatically
extends to the maximum time.
The unit will enter or exit the permanent TEST
mode (Store fixture test mode).
□
□
Lamp flashes 3 times = Store test mode
Lamp flashes 1 time = Back to normal
function
On-TiME:
1 min, 5 min, or 10 min. Lights stay for the
time set, after motion is no longer detected.
1min TIME
Smart
5
DUSK
10
LEARN
Eco
Using Manual Override Mode
8
Manual mode overrides the motion sensor (C) and
“ON-TIMES” control so the lights will operate in
“ON” mode at full brightness. This feature only
works at night for 6 hours.
ON
ON
OFF
OFF
The motion sensor (C) will reset to motion sensing
mode. Manual mode can be toggled on and off
using a wall switch.
Turn the light switch Off and back On
again within 0.2 to 1.5 seconds.
□
To manually turn the lights “ON”, turn the light
switch OFF and back ON again between 0.2
seconds to 1.5 seconds.
□
To cancel the manual override mode, turn the
light switch OFF and back ON again between 0.2
seconds to 1.5 seconds.
NOTE: If the power to the light fixture is off for more
than 5 seconds, allow the motion sensor to warm up prior
to switching to manual mode.
9
HOMEDEPOT.com
Please contact 1-866-308-3976 for further assistance.
151209-IQA HD-2703-FA.indd
9
9/12/2015 10:18:36 AM
Care and Cleaning
□
To prolong the original appearance, clean with clear water and soft, damp cloth only.
□
□
Do not use paints, solvents, or other chemicals on this light fixture. They could cause a premature deterioration
of the finish. This is not a defect in the finish and will not be covered by the warranty.
Do not spray with a hose or power washer.
Troubleshooting
Problem
Possible cause
solution
The light will not come on.
□
□
The light switch is turned off.
□
□
Turn the light switch on.
The fuse is blown or the circuit breaker is
turned off.
Replace the fuse or turn
the circuit breaker on.
□
□
Daylight turn-off (photocell) is in effect.
□
□
Recheck after dark.
The circuit wiring is incorrect, if this is a
new installation.
Verify the wiring is
correct.
□
The motion sensor is aimed in the wrong
direction.
□
Re-aim the motion sensor
to cover the desired area.
The light comes on during
the day.
□
□
The motion sensor may be installed in a
relatively dark location.
□
□
The light fixture is
operating normally under
these circumstances.
Dusk Learn was set at day condition.
Reset the dusk learn
button by pushing once
at the desired level of
darkness, or put back
in the factory setting by
pushing the dusk learn
button twice within 5
seconds.
The light comes on for no
apparent reason.
□
□
The motion sensor may be sensing small
animals or automobile traffic.
□
□
Re-aim the motion sensor.
The light fixture is
operating normally under
these circumstances.
The HI-LO switch is set to Dusk to Dawn or
Dusk Timer mode.
The lights turn off too late The light fixture may be installed in a relatively
in Dusk-to-Dawn setting. dark location.
Reset the light level (lux) at
which the sensor operates with
the dusk learn button. This will
allow you to reset the outside
light level at which the motion
sensor becomes active and the
Hi-Lo feature operates.
10
151209-IQA HD-2703-FA.indd 10
9/12/2015 10:18:36 AM
Troubleshooting (continued)
Problem
Possible cause
solution
The lights stay on
continuously.
□
□
□
A lamp is positioned too close to the motion
sensor or pointed at nearby objects that
cause heat to trigger the motion sensor.
□
Reposition the lamp
away from the motion
sensor or nearby
objects.
The motion sensor may be picking up a heat
source like an air vent, dryer vent, or brightly
painted, heat-reflective surface.
The motion sensor is in manual mode.
□
□
Turn the light switch
that operates the
fixture Off and back On
again within 0.2 to 1.5
seconds.
□
The light fixture is on the same circuit as a
motor, transformer, or fluorescent bulb.
Install the light fixture
on a circuit without
motors, transformers, or
fluorescent bulbs.
The lights flash on and off.
□
Heat or light from the lamp head may be
turning the motion sensor On and Off.
□
□
Reposition the lamp
head from the motion
sensor.
Reposition the motion
sensor.
□
□
Heat is being reflected from other objects
and may be turning the motion sensor on
and off.
The motion sensor is in “TEST” mode and
warming up.
□
Flashing is normal
under these conditions.
11
HOMEDEPOT.com
Please contact 1-866-308-3976 for further assistance.
151209-IQA HD-2703-FA.indd 11
9/12/2015 10:18:37 AM
Questions, problems, missing parts? Before returning to the store,
call Defiant Customer Service
8 a.m. - 7 p.m., EST, Monday-Friday, 9 a.m. - 6 p.m., EST, Saturday
1-866-308-3976
HOMEDEPOT.COM
Retain this manual for future use.
151209-IQA HD-2703-FA.indd 12
9/12/2015 10:18:37 AM
|